Speaker Terminals, Terminal Spacers and Bi-wire Connectors
Pairs of high quality speaker terminals. The terminals have a gold plated brass
body with 32mm gold plated shafts which are fully threaded. Supplied as one red-banded terminal and one
black-banded. Insulated terminal spacers, (mounting kits), are sold separately. These permit the
use of the terminals in either wood or metal cabinets. However, the optimum choice for metal cabinets would
be the somewhat shorter terminals with a 20mm shaft length. There is a choice of 19mm or 30mm width spacing
for the mounting kits.
Gold Plated Speaker Terminals. One Red, One Black: Sold in Pairs.
Pairs of high quality ABS speaker terminals. These have moulded
ABS end-caps with metal inserts and gold-plated brass shafts of length either 20mm or 32mm. A 4mm shaft cross drilling
and a 4mm rear drilling permit the use of either Banana Plugs or stripped wire ends as connectors. Supplied as
one red-capped and one black-capped terminal.
Insulated spacers, (mounting kits), are sold separately and permit the use of these terminals in either a wood or metal
ABS Speaker Terminals. 32mm length. One Red, One Black: Sold in Pairs.
These spacers are specifically designed for use with our Gold and ABS terminal pairs.
Whilst the terminals can be used without these spacers, MDF panels eventually shrink resulting in loose connections which can
twist in their housings. This may result in strained or broken internal connections. The spacers prevent all tendency
for the terminals to twist and are available in two width fittings of (19 and 30)mm.
The 30mm version cannot be confused with the European 19mm main pin connectors and so is inherently safer.
It is also easier to use for those with chunky fingers.
Loudspeaker Terminal Mounting Kits for (32 & 20)mm shafts
Terminal Mounting Kits. Priced each.
Mounting Kit: 30mm spacing between Terminals
Mounting Kit: 19mm spacing between Terminals
A pair of speaker terminals housed in a hard plastic rectangular tray. The
connectors have all metal cable terminations with gold plated inserts. The terminals are cross drilled to accept wire
diameters of up to 4mm.
The rear drilling can accept 4mm Banana Plugs or bare wires as required. A panel cut-out of (56 by 75)mm is required
for installation. (Sold in pairs).
Twin Terminal Tray - 02
Twin Terminal Loudspeaker Tray: Rectangular
A pair of speaker terminals mounted on a hard plastic circular cut-out. Gold plated
terminals. Cross drilled to accept wire up to 4mm diameter. Rear drilling accepts 4mm Banana Plugs.
Panel cut-out 48.5mm circle. (Sold in pairs).
Twin Terminal Tray - 03
Twin Terminal Gold-Plated Connectors: Round
A pair of loudspeaker connectors mounted on a hard plastic circular cut-out. The terminals have
ABS heads for cable clamping. The shafts are Cross drilled to accept wire up to 4mm diameter. The rear cap head
accepts 4mm Banana Plugs. Panel Cut-out 48.5mm circle. (Sold in pairs).
Twin Terminal Tray - 04
Twin Terminal Tray, ABS Connectors: Round
A Bi-wire connector plate. Constructed with four gold plated brass terminals mounted on
a rigid plastic moulding. The terminals feature two gold plated bridging / shorting straps and will accept M5 spade
or ring fittings on the rear connector face. Cross drilled to accept wire up to 4mm diameter with a rear drilling which
can also accept 4mm Banana Plugs. These Bi-wire connectors can be used for bi-wiring, two-driver, conventional loudspeaker
systems provided the two sections of the crossover can be electrically split. In bi-amping applications the crossovers,
often electronic, are placed before the amplifiers. The amplifier outputs are then connected to the Bi-wire connectors
and hence to the individual speakers. Each connector plate requires a rear panel cut-out of (73 by 94)mm. (Sold in pairs).